Breakout Garden ↔ Qwiic compatibility
Connecting Breakout Garden and Qwiic — and the reverse, Qwiic to Breakout Garden. Here's the verdict, the exact part, and the voltage catch.
Breakout Garden uses a 5-pin edge connector, so Breakout Garden → Qwiic needs an adapter. Its extra pin carries an interrupt line if your board uses one.
Side by side
| Spec | Breakout Garden | Qwiic |
|---|---|---|
| Connector | 5-pin edge | JST-SH |
| Pitch | 2.54 mm | 1 mm |
| Logic | 3v3 | 3v3 |
Why this verdict
What actually decides Breakout Garden ↔ Qwiic
The connector. Breakout Garden uses a 5-pin edge at 2.54 mm; Qwiic uses a JST-SH at 1 mm. Different housings and different pitch mean no cable mates them directly — an adapter is doing real work, not just convenience.
The pin order. Breakout Garden runs 3V3 → SDA → SCL → INT → GND while Qwiic runs GND → 3V3 → SDA → SCL. A plug that fits mechanically but disagrees on order is the worst case: it looks right and the bus stays silent, or worse, power meets a data line. Use an adapter made for this pair — see the pinout visualizer to see the two side by side.
The voltage. Breakout Garden is 3.3 V only; Qwiic is 3.3 V only. i2c has no negotiation — whatever the host drives lands on every device. If one side is 3.3 V-only and your host is 5 V, a level shifter isn't optional, it's the difference between a working bus and a dead sensor. The compatibility checker surfaces this for any combination.
Bridged, it's still one ordinary i2c bus: unique addresses per device (conflicts have fixes), pull-ups in parallel, and a 400 pF capacitance budget. Nothing answering after you connect? Run an i2c scan — it separates a cable problem from an address problem in seconds.
Questions
Breakout Garden & Qwiic FAQ
Can you connect Breakout Garden to Qwiic directly?
Not directly — Breakout Garden (5-pin edge) and Qwiic (JST-SH) use different connectors, so you need an adapter. Breakout Garden uses a 5-pin edge connector, so Breakout Garden → Qwiic needs an adapter. Its extra pin carries an interrupt line if your board uses one.
Do I need a level shifter between Breakout Garden and Qwiic?
Only if the logic voltages differ — typically a 5 V host with a 3.3 V-only device. Breakout Garden is 3v3; Qwiic is 3v3. If both ends run at 3.3 V, no level shifter is needed.
Is the Breakout Garden pinout the same as Qwiic?
No. Breakout Garden is wired 3V3 / SDA / SCL / INT / GND and Qwiic is GND / 3V3 / SDA / SCL. That difference is exactly why you can't just force a plug that seems to fit — an adapter built for this pairing re-orders the conductors for you.
Can I chain Breakout Garden and Qwiic devices on one bus?
Physically yes, once the connectors are bridged — electrically it's still one i2c bus, so the usual rules decide it. Every device needs a unique address, all the pull-up resistors sit in parallel, and total cable capacitance has a 400 pF ceiling. Mixing ecosystems doesn't change the bus; it just changes the plug.
Related pairings
Other Breakout Garden and Qwiic combinations
Every pairing is pre-answered — here are the rest involving either of these two. The verdict on each tile is the cautious one, since it assumes nothing about your host's voltage.
Or start from a standard: Breakout Garden and Qwiic each list their pinout and every ecosystem they reach. The full pairing index has all 15, and the compatibility checker does it interactively.